Introduction to SCR low-temperature denitrification, SCR denitration advantages, characteristics and principles

SCR low-temperature denitrificationis an efficient, stable and environment-friendly flue gas denitrification technology.，the advantage is The initial investment of technology may be high, but in the long run, its economic feasibility is remarkable. The high-efficiency denitration ability of SCR low-temperature denitrification technology can significantly reduce the environmental emission cost of enterprises and avoid fines and legal risks due to illegal emissions. In addition, SCR low-temperature denitrification technology can also reduce operating costs and improve the economic benefits of enterprises by recycling heat energy.、There are many kinds of catalysts used in the technology, including vanadium-based catalysts and titanium-based catalysts, which can promote the chemical reaction between reductant and NOx at a lower temperature. At the same time, the active components and carrier materials of the catalyst are constantly being developed and improved to improve its catalytic efficiency and service life. This enables the SCR low-temperature denitrification technology to maintain efficient denitrification capability in a wider temperature range and more complex flue gas conditions.、It is famous for its high-efficiency denitration ability, which can usually reach more than 90% denitration efficiency. This means that the SCR low-temperature denitrification technology can significantly reduce the concentration of nitrogen oxides (NOx) in flue gas and make it meet strict environmental protection emission standards. This high-efficiency denitration ability is mainly due to the promotion of the catalyst, which makes the chemical reaction between reductant and NOx more rapid and thorough.、The by-products produced by the technology are mainly nitrogen and water vapor, which are harmless to the environment and will not cause secondary pollution. Compared with the traditional wet flue gas denitrification technology, the SCR low-temperature denitrification technology does not need to use a lot of water resources and will not produce pollutants such as wastewater, which is more in line with the requirements of environmental protection and sustainable development.、The by-products produced by the technology are mainly nitrogen and water vapor, which are harmless to the environment and will not cause secondary pollution. Compared with the traditional wet flue gas denitrification technology, the SCR low-temperature denitrification technology does not need to use a lot of water resources and will not produce pollutants such as wastewater, which is more in line with the requirements of environmental protection and sustainable development.，features include Strong adaptability, Efficient denitration, Stable operation, High denitration efficiency and Mature and stable technology。

1、Brief introduction of SCR low-temperature denitrification

SCR low-temperature denitrificationit refers to the process of removing nitrogen oxides from flue gas to reduce environmental pollution. NOx is a pollutant harmful to the atmospheric environment, which has strong irritation and toxicity, and will lead to environmental problems such as acid rain and photochemical smog, and also endanger human health. The main principle of flue gas denitrification technology is to reduce NOx to nitrogen and water by adding appropriate reducing agent or catalyst in the combustion process or flue gas treatment system, so as to reduce NOx emission.，is a common SCR low-temperature denitrification，support customization。

SCR low-temperature denitrification

2、Advantages of SCR low-temperature denitrification principle

SCR low-temperature denitrificationin the course of work,Ammonia gas or other suitable reducing agent (such as urea aqueous solution) is sprayed into the flue gas upstream of the catalyst at high temperature. Under the action of catalyst, the reducing agent selectively reacts with nitrogen oxides (NOx) in flue gas to generate pollution-free nitrogen and water vapor. Because NH3 is selective, it only reacts with NOx and basically does not react with O2, so this technology is called selective catalytic reduction denitrification.，It can be used for Promote sustainable development, Meet the requirements of environmental protection, Flue gas denitrification, Meet the requirements of environmental protection, Promote sustainable development, Flue gas denitrification and so on，generally, it is composed of Flue gas mixing and distribution system, Temperature control and monitoring system, Catalyst supply system, Catalyst reactor, control system and other major components，productThe structural design is more advanced and reasonable.，is a kind of high quality and low price SCR low-temperature denitrification，it is an ideal choice for customers to buy SCR low-temperature denitrification。

SCR low-temperature denitrification

3、SCR low-temperature denitrification application

SCR low-temperature denitrificationWidely used inenvironmental protection,Improve product quality,Meet the requirements of environmental protection,Promote sustainable development,environmental protection and so on，at work,Under the action of catalyst, reducing agents (such as ammonia, urea, etc.) react with nitrogen oxides in flue gas to convert them into harmless nitrogen and water vapor.，it mainly includes Flue gas mixing and distribution system, Temperature control and monitoring system, Catalyst reactor, Catalyst supply system and control system，It is famous for its high-efficiency denitration ability, which can usually reach more than 90% denitration efficiency. This means that the SCR low-temperature denitrification technology can significantly reduce the concentration of nitrogen oxides (NOx) in flue gas and make it meet strict environmental protection emission standards. This high-efficiency denitration ability is mainly due to the promotion of the catalyst, which makes the chemical reaction between reductant and NOx more rapid and thorough.、The technology is suitable for many industries and processes, such as coal-fired power plants, iron and steel smelting, cement production and so on. These industries will produce a large number of NOx emissions in the production process, and the SCR low-temperature denitrification technology can provide effective denitrification solutions for them. In addition, the gate technology can be adjusted and optimized according to different flue gas components and emission requirements to meet different denitration requirements.、There are many kinds of catalysts used in the technology, including vanadium-based catalysts and titanium-based catalysts, which can promote the chemical reaction between reductant and NOx at a lower temperature. At the same time, the active components and carrier materials of the catalyst are constantly being developed and improved to improve its catalytic efficiency and service life. This enables the SCR low-temperature denitrification technology to maintain efficient denitrification capability in a wider temperature range and more complex flue gas conditions.、Intelligent control is gradually realized. By integrating advanced control system and sensor technology, the SCR low-temperature denitrification can monitor the composition and emission concentration of flue gas in real time, and automatically adjust the injection amount of reductant and the active state of catalyst to ensure the stability and reliability of denitrification efficiency.、Technology has been developed and applied for many years, and it is mature and stable. The SCR low-temperature denitrification has high reliability and stability, and can maintain stable denitrification efficiency under various working conditions. In addition, the SCR low-temperature denitrification technology has good adaptability and adjustability, and can be adjusted and optimized according to different flue gas components and emission requirements.，is a kind of SCR low-temperature denitrification manufactured by One-combustion energy saving。

SCR low-temperature denitrification

4、Functional advantages of SCR low-temperature denitrification

SCR low-temperature denitrifications have the following advantages.

1. Wide applicability

SCR low-temperature denitrification technology is suitable for many industries and processes, such as coal-fired power plants, iron and steel smelting, cement production and so on. These industries will produce a large number of NOx emissions in the production process, and the SCR low-temperature denitrification technology can provide effective denitrification solutions for them. In addition, the gate technology can be adjusted and optimized according to different flue gas components and emission requirements to meet different denitration requirements.

2. Mature and stable technology

SCR low-temperature denitrification technology has been developed and applied for many years, and the technology is mature and stable. The SCR low-temperature denitrification has high reliability and stability, and can maintain stable denitrification efficiency under various working conditions. In addition, the SCR low-temperature denitrification technology has good adaptability and adjustability, and can be adjusted and optimized according to different flue gas components and emission requirements.

3. Intelligent control and convenience of operation

The SCR low-temperature denitrification has gradually realized intelligent control. By integrating advanced control system and sensor technology, the SCR low-temperature denitrification can monitor the composition and emission concentration of flue gas in real time, and automatically adjust the injection amount of reductant and the active state of catalyst to ensure the stability and reliability of denitrification efficiency.

4. High efficiency denitration capacity

Gate is famous for its high efficiency of denitration, which can usually reach more than 90% denitration efficiency. This means that the SCR low-temperature denitrification technology can significantly reduce the concentration of nitrogen oxides (NOx) in flue gas and make it meet strict environmental protection emission standards. This high-efficiency denitration ability mainly benefits from the promotion of catalyst, which makes the chemical reaction between reductant and NOx more rapid and thorough.

5. Diversity and high efficiency of catalysts

There are many kinds of catalysts used in the SCR low-temperature denitrification technology, including vanadium-based catalysts and titanium-based catalysts, which can promote the chemical reaction between reductant and NOx at low temperature. At the same time, the active components and carrier materials of the catalyst are constantly being developed and improved to improve its catalytic efficiency and service life. This enables the SCR low-temperature denitrification technology to maintain high efficiency of denitration in a wider temperature range and more complex flue gas conditions.

SCR low-temperature denitrification

5、Introduction of SCR low-temperature denitrification characteristics

SCR low-temperature denitrification has the following characteristics

1. selectivity

Under the action of catalyst, the reducing agent mainly reacts with NOx selectively, but less with other components (such as oxygen) in flue gas, thus reducing unnecessary consumption.

2. energy saving and environmental protection

This technology can effectively reduce NOx emission in flue gas, reduce environmental pollution, and at the same time, it has stable operation and low energy consumption, which meets the requirements of energy saving and environmental protection.

3. Strong adaptability

SCR low-temperature denitrification technology can meet the needs of flue gas denitrification under different working conditions and has a wide range of applications.

4. Mature technology

After years of development and application, SCR low-temperature denitrification technology is very mature and has a wide application prospect.

5. Small secondary pollution

The by-products produced in the SCR low-temperature denitrification opening process are nitrogen and water vapor, and there is no secondary pollution problem.

SCR low-temperature denitrification

SCR low-temperature denitrificationthe main features are energy saving and environmental protection, Good selectivity, Environment friendly, Environmental protection and pollution-free and Stable operation，the product looks atmospheric.，multifunctional, with functions such as environmental protection, Promote sustainable development, environmental protection, Improve energy efficiency and Improve working conditions。