Introduction to Rotary bottom annular heating furnace, forging furnace advantages, characteristics and principles

Rotary bottom annular heating furnaceIt is a kind of equipment which uses gas as fuel and is specially used for heating metal before forging.，it has the characteristics of Strong adaptability, energy-efficient, Easy to control, Stable and reliable and Easy to maintain，is a Rotary bottom annular heating furnace。The following is to introduce the Rotary bottom annular heating furnace:

1、Brief introduction of Rotary bottom annular heating furnace

Rotary bottom annular heating furnaceIt is an efficient, energy-saving and environment-friendly metal heating device.，The metal material can be heated to the required temperature in a short time, and the production efficiency is improved.、Adopting advanced combustion technology and materials, it has a long service life and low maintenance cost.、Suitable for forging and heating of various metal materials, including steel, aluminum and copper. At the same time, it can also be used in metal heat treatment, tempering and other technological processes.、The use of clean and environmentally friendly natural gas as fuel effectively avoids the adverse effects of chemical reactions between impurities such as coal-fired furnaces and forgings during heating. At the same time, natural gas has high calorific value and high combustion temperature, and the combustion temperature can be further increased by preheating air and fuel. In addition, the gas forging heating furnace also has good heat loss control ability and intelligent control system, which can accurately adjust the ratio of air to natural gas, ensure full combustion of natural gas, and reduce mechanical incomplete combustion and chemical incomplete combustion.、It has the advantages of high heating efficiency, high energy utilization, accurate temperature control, good environmental protection performance, simple operation and strong adaptability.。

Rotary bottom annular heating furnace

2、Structural characteristics of Rotary bottom annular heating furnace

The Rotary bottom annular heating furnace has the following structure

1. Waste heat recovery system

Recover the waste heat in the exhaust gas of heating furnace to improve the energy utilization efficiency.

2. Radiation chamber

The heat load of the main place for Rotary bottom annular heating furnace heat exchange accounts for about 70%-80% of the whole furnace. The furnace tube in the radiation room conducts heat through flame or high-temperature flue gas, which is mainly radiant heat, so it is called radiation tube.

3. furnace chamber

A space for holding metallic materials for heating.

4. combustor

The device that mixes natural gas with combustion-supporting air and ejects it is the core component of the heating furnace.

5. convection chamber

The material is heated by convection heat transfer of high temperature flue gas discharged from the radiation chamber. Flue gas washes the tube wall of the furnace tube at a high speed to carry out effective convection heat transfer, and its heat load accounts for about 20%-30% of the whole furnace. The convection chamber is generally arranged above the radiation chamber, and some are placed on the ground alone. In order to improve the heat transfer effect, nail head tubes or finned tubes are often used in furnace tubes.

Rotary bottom annular heating furnace

3、Rotary bottom annular heating furnace video

You can buy Rotary bottom annular heating furnace according to your needs and show you product videos.。

Rotary bottom annular heating furnace

As you can see from the live video.，One-combustion energy saving multifunctional, with functions such as hardening and tempering, Forging heating, quench, Casting heating and temper。

4、Rotary bottom annular heating furnace use

The purpose of Rotary bottom annular heating furnace is introduced as follows:

1. Metal forging heating

The Rotary bottom annular heating furnace can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

2. Metal tempering

By properly heating and cooling the metal material, the Rotary bottom annular heating furnace can realize the quenching and tempering treatment of the metal. This is helpful to adjust the hardness and toughness of metal to meet the needs of different workpieces.

3. Energy conservation and environmental protection

The Rotary bottom annular heating furnace uses clean energy as fuel, which has lower emissions and higher energy efficiency than traditional coal-fired or oil-fired stoves. This is helpful to reduce environmental pollution and realize green production.

4. Metal forging heating

The Rotary bottom annular heating furnace can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

5. Metal heat treatment

In addition to forging heating, Rotary bottom annular heating furnaces can also be used for metal heat treatment processes, such as annealing and tempering. These processes can improve the microstructure and properties of metal materials, and improve their service life and mechanical properties.

Rotary bottom annular heating furnace

5、Rotary bottom annular heating furnace characteristics

The Rotary bottom annular heating furnace features are as follows:

1. Easy to maintain

The structural design of the Rotary bottom annular heating furnace is reasonable and easy to maintain, which reduces the operating cost and failure rate of the equipment.

2. Strong adaptability

The Rotary bottom annular heating furnace can be used for forging and heating of bar, round steel, square steel, steel plate and other metal materials, and has a wide range of applications.

3. Easy to control

The combustion system and ventilation system of the Rotary bottom annular heating furnace can be adjusted as required to accurately control the temperature and atmosphere in the furnace and meet the heating requirements of different metal materials.

4. Strong adaptability

The Rotary bottom annular heating furnace is suitable for forging and heating of various metal materials and has a wide range of applications.

5. Stable and reliable

The Rotary bottom annular heating furnace has a stable combustion system and temperature control system, which can ensure the uniformity and stability of the temperature in the furnace, thus improving the quality and production efficiency of forged products.

Rotary bottom annular heating furnace

6、Rotary bottom annular heating furnace quotation

The Rotary bottom annular heating furnace price is introduced as follows:

1. product costs

The manufacturing cost has a great influence on the price. There are many cost factors, including the purchase of raw materials and the quality of products. These factors are all cost inputs. One-combustion energy saving has made a strong balance between the cost input and the sales price, so that the quality of our products can be guaranteed and the comprehensive price of products can reach the degree of customer satisfaction.

2. Model size

The same product, even with different specifications and models and different configurations, has different costs, so the price will be different.

3. product function

The more functions a product has, the higher its manufacturing cost, so that the product can be used by customers as much as possible, which can create more useful value for customers, so the price will be higher.

4. market factors

When the market demand for Rotary bottom annular heating furnace is relatively high, manufacturers will raise the price in order to get more profits. On the contrary, when the market demand for this product is low, manufacturers will lower the price in order to sell the remaining products as soon as possible.

5. mass discrepancy

The Rotary bottom annular heating furnace is made of high-quality materials, and the cost of the product is high, so the price of the product will also rise. One-combustion energy saving has always adhered to high quality in the construction of Rotary bottom annular heating furnace and won the trust of customers.

Rotary bottom annular heating furnace

Rotary bottom annular heating furnaceCommonly used inMetal heat treatment,Metal melting and casting,Energy conservation and environmental protection,Improve production efficiency,Metal melting and casting and so on，the product looks atmospheric.，the main structure includes recovery of waste heat, combustor, ventilation system, Radiation chamber, combustor and so on。