What is a Well type heating quenching furnace? How much is the price of the heating furnace?

Well type heating quenching furnaceIt is a kind of equipment which uses gas as fuel and is specially used for heating metal before forging.，Mainly used forMetal melting and casting,Metal forging heating,Energy conservation and environmental protection,Metal melting and casting andMetal heat treatment，Adopting advanced combustion technology and control system can realize full combustion of natural gas and improve combustion efficiency. At the same time, some equipment is also equipped with waste heat recovery system, which can further recycle the waste heat in exhaust smoke and improve energy utilization efficiency.、It can improve the plasticity and fluidity of metal materials, reduce the difficulty and cost of forging, and improve product quality and production efficiency.、The use of clean and environmentally friendly natural gas as fuel effectively avoids the adverse effects of chemical reactions between impurities such as coal-fired furnaces and forgings during heating. At the same time, natural gas has high calorific value and high combustion temperature, and the combustion temperature can be further increased by preheating air and fuel. In addition, the gas forging heating furnace also has good heat loss control ability and intelligent control system, which can accurately adjust the ratio of air to natural gas, ensure full combustion of natural gas, and reduce mechanical incomplete combustion and chemical incomplete combustion.、Usually equipped with intelligent control system, it can automatically adjust the parameters such as gas supply and air flow according to the heating demand, and realize accurate control of the temperature and atmosphere in the furnace.、Natural gas is used as a heat source, resulting in less waste gas and smoke after combustion, and less pollution to the environment. This will help reduce industrial emissions and improve the atmospheric environment.，it is an ideal choice for customers to buy Well type heating quenching furnace。The following is to introduce the Well type heating quenching furnace:

1、Brief introduction of Well type heating quenching furnace

Well type heating quenching furnaceIt is a kind of heating equipment using natural gas as fuel, which is mainly used to heat metal materials to the required forging temperature in a short time.，the product looks beautiful.，at the start of the operation,Heat of combustion based on fuel. Natural gas is sprayed from the burner, mixed with combustion-supporting air and burned to produce high-temperature flame and smoke. These high-temperature flames and smoke transfer heat to the metal materials in the furnace by radiation and convection, so that they gradually heat up to the temperature required for forging.，is a common Well type heating quenching furnace，customizable。

Well type heating quenching furnace

2、Well type heating quenching furnace HD real picture

Well type heating quenching furnace high-definition picture display, all-round shooting without dead ends, for our customers to visit.。

Well type heating quenching furnace

Note: All the pictures in this article were taken by One-combustion energy saving manufacturer.。

3、Well type heating quenching furnace structure composition

The Well type heating quenching furnace has the following structure

1. convection chamber

The high-temperature flue gas discharged from the radiation chamber is used for convective heat transfer to further heat the metal materials.

2. combustor

The device that mixes natural gas with combustion-supporting air and ejects it is the core component of the heating furnace.

3. furnace chamber

A space for holding metallic materials for heating.

4. Radiation chamber

The heat load of the main place for Well type heating quenching furnace heat exchange accounts for about 70%-80% of the whole furnace. The furnace tube in the radiation room conducts heat through flame or high-temperature flue gas, which is mainly radiant heat, so it is called radiation tube.

5. Waste heat recovery system

Used to recover the exhaust heat of the heating furnace. There are two kinds of recovery methods, one is to recover by preheating combustion air, so that the recovered heat can return to the furnace again; The other is to use another recovery system to recover heat. The former is called air preheating mode, and the latter is usually called waste heat boiler mode.

Well type heating quenching furnace

4、Well type heating quenching furnace advantage

The advantages of Well type heating quenching furnace are as follows:

1. Extend the service life of equipment

The Well type heating quenching furnace adopts advanced combustion technology and materials, which has a long service life and low maintenance cost.

2. Rapid temperature rise

The Well type heating quenching furnace can heat the metal material to the required temperature in a short time, which improves the production efficiency.

3. Improve product quality

Because the Well type heating quenching furnace can realize uniform heating and precise control, it is helpful to improve the product quality and yield of metal materials.

4. Uniform heating

The Well type heating quenching furnace adopts regenerative combustion system or advanced burner design, which can realize uniform distribution of temperature in the furnace, ensure uniform heating of metal materials and improve product quality.

5. Improve product quality

Because the Well type heating quenching furnace can realize uniform heating and precise control, it is helpful to improve the product quality and yield of metal materials.

Well type heating quenching furnace

5、How much is the Well type heating quenching furnace?

The Well type heating quenching furnace price is introduced as follows:

1. raw material

The quality of material selection is one of the main factors that directly affect the Well type heating quenching furnace. If the quality of material selection is better, the price may be more expensive. Therefore, customers must first understand the quality of material selection before purchasing products, and then compare whether the quality and price match.

2. company strength

Our company's expected profit value of Well type heating quenching furnace is relatively low, and adopts the sales policy of small profits but quick turnover, so the price positioning of Well type heating quenching furnace is relatively low.

3. regional difference

The consumption level will be different in different regions. When pricing equipment, many manufacturers often set the price according to the consumption level of the region. If the consumption level is high, the price will be correspondingly high, otherwise, the price will be very low.

4. Brand strength

At present, there are various brands of Well type heating quenching furnace in Shandong(Province). The performance, quality and after-sales of products under different brands are different, and the prices of Well type heating quenching furnace are different.

5. Product technology

Different manufacturers have different advanced technologies, different production processes and different performances, and the price difference is naturally quite large.

Well type heating quenching furnace

6、One-combustion energy saving company service

Our company will not only provide customers with excellent quality Well type heating quenching furnace, but also choose a series of high-quality services such as appropriate specifications and models according to their actual needs.。

One-combustion energy saving

Well type heating quenching furnaceit can be used in petroleum, chemical industry, machinery, metallurgy, surface treatment and other industries，the principle is simple.The high-temperature flame and flue gas generated when the fuel burns in the furnace are used as heat sources to heat the medium flowing in the tube to reach the specified process temperature. Fuel is ejected from the burner and burned, resulting in high-temperature flame and high-temperature flue gas. The high-temperature flame transfers heat to the furnace tube in the radiation chamber through radiation, and then to the medium in the furnace tube. The high-temperature flue gas enters the convection chamber of the heating furnace upward due to the suction force of the chimney or the action of the induced draft fan, and the heat is transferred to the furnace tube in the convection chamber by convection, and then to the medium in the furnace tube.，the product looks atmospheric.。