What is a High pressure Roots vacuum pump? Introduction to the principle of blower structure

High pressure Roots vacuum pumpis a positive displacement blower with forced gas transmission characteristics.，at the start of the operation,When the motor drives one impeller to rotate, the other impeller will rotate synchronously at the same speed and in the opposite direction under the action of the synchronous gear. In the process of rotation, because the gaps between impeller and impeller, impeller and casing, impeller and wallboard are very small, a vacuum state is formed at the air inlet, and air is sucked into the air inlet cavity under the action of atmospheric pressure. As the impeller continues to rotate, two blades of each impeller, the wallboard and the casing form a sealed cavity, and the air in the air inlet cavity is continuously brought to the exhaust cavity by the sealed cavity formed by the two blades. Because the impellers in the exhaust cavity are meshed with each other, the air between the two blades is squeezed out. After continuous inhalation and extrusion, air is continuously transported from the air inlet to the air outlet, completing the whole gas transportation process.，it has the functions of dry, material fluidization, desulfurization oxidation, sewage disposal and pressurized transportation，It is a product series that integrates Pressurized transportation, mix, pick up the suction, Material fluidization and material handling，is a High pressure Roots vacuum pump newly developed by hyde powder。The following is to introduce the High pressure Roots vacuum pump:

1、Brief introduction of High pressure Roots vacuum pump

High pressure Roots vacuum pumpis a double impeller synchronous compression machine, belonging to a positive displacement blower.。

High pressure Roots vacuum pump

2、High pressure Roots vacuum pump use

High pressure Roots vacuum pumpIt has a wide range of uses, including mix, pick up the suction, Desulfurization oxidation, dry and aquaculture，in the course of work,Gas is compressed and transported based on the relative motion of two lobed rotors in the cylinder. When the two rotors rotate, the volume between them changes constantly, thus realizing the suction, compression and discharge of gas.，the advantage is Small size and small floor space make it easy to arrange and install in places with limited space.、The air volume is directly proportional to the rotating speed, so its air output is very stable and basically unaffected by pressure changes. This characteristic makes the High pressure Roots vacuum pump perform well in many situations where stable airflow is needed.、The structural form of the three-blade rotor and the reasonable structure of the air inlet and outlet in the shell make the fan have small vibration and low noise.、In the process of air intake and exhaust, the High pressure Roots vacuum pump will not produce air pulsation, which means that it does not need an additional buffer gas tank to output gas smoothly. This is particularly important for processes that require stable airflow.、It has high efficiency and can realize gas transportation and pressurization with low energy consumption.。

High pressure Roots vacuum pump

3、High pressure Roots vacuum pump HD real shot

You can buy High pressure Roots vacuum pump according to your needs and show you High pressure Roots vacuum pump videos.。

High pressure Roots vacuum pump

As you can see from the live video.，Shandong Haide Fenti Engineering Co., Ltd. The structural design is more advanced and reasonable.，it is mainly composed of case, fuel tank, muffler, rotator and impeller。

4、High pressure Roots vacuum pump function

High pressure Roots vacuum pumpmultifunctional, with functions such as pick up the suction, mix, exhaust emission, cool and ventilation，the advantage is Due to the adoption of synchronous gear transmission and small gap design, the High pressure Roots vacuum pump runs stably and reliably, without contact and wear parts, and has a long service life.、Because of the design of three-blade rotor, the High pressure Roots vacuum pump has little vibration and low noise during operation, and the operation is stable and reliable、Simple structural design, stable and reliable operation and convenient maintenance. This enables it to maintain high working efficiency and stability in long-term operation.、The structural form of the three-blade rotor and the reasonable structure of the air inlet and outlet in the shell make the High pressure Roots vacuum pump less vibration and noise.、Small size and small floor space make it easy to arrange and install in places with limited space.，it has the characteristics of low noise, wide application range, convenient manufacture, strong adaptability and energy-efficient，the main structure includes case, muffler, fuel tank, impeller and wallboard，High pressure Roots vacuum pumpThe structural design is simple, novel and special.，The air volume is directly proportional to the rotating speed, so its air output is very stable and basically unaffected by pressure changes. This characteristic makes the High pressure Roots vacuum pump perform well in many situations where stable airflow is needed.、In the process of air intake and exhaust, the High pressure Roots vacuum pump will not produce air pulsation, which means that it does not need an additional buffer gas tank to output gas smoothly. This is particularly important for processes that require stable airflow.、The structural form of the three-blade rotor and the reasonable structure of the air inlet and outlet in the shell make the High pressure Roots vacuum pump less vibration and noise.、It has high efficiency and can realize gas transportation and pressurization with low energy consumption.、Because of the design of three-blade rotor, the High pressure Roots vacuum pump has little vibration and low noise during operation, and the operation is stable and reliable。

High pressure Roots vacuum pump

5、Structural advantages of High pressure Roots vacuum pump

The High pressure Roots vacuum pump structure is introduced as follows:

1. fuel tank

Mainly used for storing lubricating oil used for lubricating gears and bearings. The oil tank is used to store lubricating oil to lubricate bearings and gears and reduce wear and friction.

2. wallboard

It is mainly used to connect the casing with the impeller, support the rotation of the impeller, and play the role of end sealing.

3. rotator

The core components are two identical lobed rotors, which usually adopt involute or epicycloid envelope design to ensure close cooperation during rotation and reduce leakage.

4. impeller

It is the rotating part of the High pressure Roots vacuum pump, which is divided into two leaves and three leaves. However, due to many advantages such as smaller air pulsation, less noise and smoother operation, the three-leaf High pressure Roots vacuum pump has gradually replaced the two-leaf High pressure Roots vacuum pump.

5. muffler

Used to reduce the noise caused by airflow pulsation when the High pressure Roots vacuum pump enters and exits.

High pressure Roots vacuum pump

6、High pressure Roots vacuum pump price advantage

The High pressure Roots vacuum pump price is introduced as follows:

1. technology content

Each customer needs different products, wants to achieve different purposes, and has different product technical design. The higher or more advanced the technical requirements, the more the product cost will be, and the price will increase with the increase of cost. On the contrary, the price will be cheaper.

2. Sales model

There are direct selling manufacturers and agents in the market. Agents are higher than direct selling manufacturers, mainly because agents get goods from manufacturers, sell them to customers and earn the difference from middlemen, so the natural price is higher.

3. Manufacturer scale

At present, there are many manufacturers of products on the market, some of which belong to direct selling manufacturers and some belong to middlemen. Direct selling manufacturers will cost less than middlemen, so the quotation for products will be lower. Therefore, it is recommended that customers buy products from direct selling manufacturers of High pressure Roots vacuum pump. In addition, even direct selling manufacturers have different capital status, strength level and technology, and the quotation for High pressure Roots vacuum pump will be different.

4. market factors

The amount of customers' demand for High pressure Roots vacuum pump in the market also has a great influence on the price. When there are many customers purchasing this product in the market and the supply quantity of manufacturers is small, the High pressure Roots vacuum pump price will be very high. On the contrary, when fewer customers purchase this product, there will be a phenomenon of oversupply, and the price of High pressure Roots vacuum pump will naturally be reduced.

5. select a qualified person

The quality of materials directly determines the cost. The worse the materials are, the lower the cost will be, and the cheaper the price will be. Of course, the materials are better and the cost is higher, so the overall quotation is naturally higher.

High pressure Roots vacuum pump

High pressure Roots vacuum pumpit has the functions of material handling, supply air, dehydrate, aeration and aquaculture，the product looks atmospheric.，is a double impeller synchronous compression machine, belonging to a positive displacement blower.。