What is a Energy saving and environmentally friendly through furnace? Introduction to the advantages and characteristics of the Forging furnace

Energy saving and environmentally friendly through furnaceIt is a forging heating device using gas as fuel.，is a popular Energy saving and environmentally friendly through furnace，Adopting advanced combustion technology and materials, it has a long service life and low maintenance cost.、The use of clean and environmentally friendly natural gas as fuel effectively avoids the adverse effects of chemical reactions between impurities such as coal-fired furnaces and forgings during heating. At the same time, natural gas has high calorific value and high combustion temperature, and the combustion temperature can be further increased by preheating air and fuel. In addition, the gas forging heating furnace also has good heat loss control ability and intelligent control system, which can accurately adjust the ratio of air to natural gas, ensure full combustion of natural gas, and reduce mechanical incomplete combustion and chemical incomplete combustion.、The user interface is friendly, and the operator is easy to use. At the same time, the equipment also has the function of fault diagnosis and alarm, which can find and deal with abnormal situations in time.、Usually equipped with intelligent control system, it can automatically adjust the parameters such as gas supply and air flow according to the heating demand, and realize accurate control of the temperature and atmosphere in the furnace.、Efficient combustion and waste heat recovery system can significantly reduce energy consumption, thus reducing operating costs.。The following is to introduce the Energy saving and environmentally friendly through furnace:

1、Brief introduction of Energy saving and environmentally friendly through furnace

Energy saving and environmentally friendly through furnaceIt is a kind of heating equipment using natural gas as fuel, which is mainly used to heat metal materials to the required forging temperature in a short time.。

Energy saving and environmentally friendly through furnace

2、Energy saving and environmentally friendly through furnace performance advantage

The advantages of Energy saving and environmentally friendly through furnace are as follows:

1. easy to operate

The operation interface of the Energy saving and environmentally friendly through furnace is friendly and easy for operators to use. At the same time, the equipment also has the function of fault diagnosis and alarm, which can find and deal with abnormal situations in time.

2. clean energy

Natural gas, as a clean energy source, produces less waste gas and dust after combustion, which has little pollution to the environment. This will help reduce industrial emissions and improve the atmospheric environment.

3. Intelligent control

The Energy saving and environmentally friendly through furnace is usually equipped with an intelligent control system, which can automatically adjust the parameters such as gas supply and air flow according to the heating demand, and realize accurate control of the temperature and atmosphere in the furnace.

4. Efficient combustion

The Energy saving and environmentally friendly through furnace adopts advanced combustion technology and control system, which can realize full combustion of natural gas and improve combustion efficiency. At the same time, some equipment is also equipped with waste heat recovery system, which can further recycle the waste heat in exhaust smoke and improve energy utilization efficiency.

5. Extend the service life of equipment

The Energy saving and environmentally friendly through furnace adopts advanced combustion technology and materials, which has a long service life and low maintenance cost.

Energy saving and environmentally friendly through furnace

3、Working principle of Energy saving and environmentally friendly through furnace

Energy saving and environmentally friendly through furnaceHeat of combustion based on fuel. Fuel gas (such as natural gas, liquefied petroleum gas, etc.) is mixed with combustion-supporting air through the burner and burned to produce high-temperature flame and flue gas. These high-temperature flames and smoke exchange heat with metal materials in the furnace, so that they gradually heat up to the temperature required for forging.，It is a kind of equipment that uses natural gas as fuel to heat metal materials and make them reach forging temperature.，Easy to control,energy-efficient,Easy to maintain,Stable and reliable,Strong adaptability。

Energy saving and environmentally friendly through furnace

4、Energy saving and environmentally friendly through furnace use

The purpose of Energy saving and environmentally friendly through furnace is introduced as follows:

1. Metal forging heating

The Energy saving and environmentally friendly through furnace can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

2. Metal tempering

By properly heating and cooling the metal material, the Energy saving and environmentally friendly through furnace can realize the quenching and tempering treatment of the metal. This is helpful to adjust the hardness and toughness of metal to meet the needs of different workpieces.

3. Improve production efficiency

The Energy saving and environmentally friendly through furnace has the advantages of fast heating speed and accurate temperature control, which can improve production efficiency. This is especially important for mass-produced forging workshops.

4. Energy conservation and environmental protection

The Energy saving and environmentally friendly through furnace uses clean energy as fuel, which has lower emissions and higher energy efficiency than traditional coal-fired or oil-fired stoves. This is helpful to reduce environmental pollution and realize green production.

5. Metal heat treatment

In addition to forging heating, Energy saving and environmentally friendly through furnaces can also be used for metal heat treatment processes, such as annealing and tempering. These processes can improve the microstructure and properties of metal materials, and improve their service life and mechanical properties.

Energy saving and environmentally friendly through furnace

5、Energy saving and environmentally friendly through furnace function

Energy saving and environmentally friendly through furnaceit has the functions of Forging heating, normalizing, temper, hardening and tempering and anneal，is a common Energy saving and environmentally friendly through furnace，it has the characteristics of Easy to maintain, Easy to control, energy-efficient, energy saving and environmental protection and Stable and reliable，it is an ideal choice for customers to buy Energy saving and environmentally friendly through furnace。

Energy saving and environmentally friendly through furnace

6、Energy saving and environmentally friendly through furnace price advantage

The Energy saving and environmentally friendly through furnace price is introduced as follows:

1. product configuration

If the comprehensive configuration of the product is higher, the selling price of the product will be higher, otherwise the price will be lower, so there is a close relationship between the configuration level and the price.

2. After-sales service level

Service factors always affect the sales price of products, and high-quality service will make customers have greater satisfaction and recognition. The service factors mainly include pre-sales service, in-sales service and after-sales service. For each stage of service, our company takes the price factor into account and makes a reasonable judgment between service and price, so that the Energy saving and environmentally friendly through furnace price and service can meet the actual needs of customers.

3. mass discrepancy

Quality is the fundamental factor that determines the price. The better the quality, the more detailed the manufacturing process, the more careful the materials are, the better the performance is, and the price will naturally be more expensive.

4. market factors

When the market demand for Energy saving and environmentally friendly through furnace is relatively high, manufacturers will raise the price in order to get more profits. On the contrary, when the market demand for this product is low, manufacturers will lower the price in order to sell the remaining products as soon as possible.

5. Product technology

Each customer needs different products, wants to achieve different purposes, and has different product technical design. The higher or more advanced the technical requirements, the more the product cost will be, and the price will increase with the increase of cost. On the contrary, the price will be cheaper.

Energy saving and environmentally friendly through furnace

Energy saving and environmentally friendly through furnacemultifunctional, with functions such as quench, heat treatment, normalizing, anneal and hardening and tempering，features include Easy to maintain, energy saving and environmental protection, energy saving and environmental protection, Stable and reliable and Strong adaptability，the advantage is Uniform heating and precise control can be realized, so it is helpful to improve the product quality and yield of metal materials.、Natural gas is mainly used as fuel, but some equipment also supports other types of gas or liquid fuel, which has strong fuel adaptability.、Suitable for forging and heating of various metal materials, including steel, aluminum and copper. At the same time, it can also be used in metal heat treatment, tempering and other technological processes.、The metal material can be heated to the required temperature in a short time, and the production efficiency is improved.、Efficient combustion and waste heat recovery system can significantly reduce energy consumption, thus reducing operating costs.。