What is a Mold quenching furnace chamber type? Introduction to the advantages and characteristics of the Forging furnace

Mold quenching furnace chamber typeIt is an important heating equipment before metal forging. It uses natural gas as fuel to heat metal materials through high-temperature flame and smoke generated by combustion to meet the requirements of forging process.，the advantage is Suitable for forging and heating of various metal materials, including steel, aluminum and copper. At the same time, it can also be used in metal heat treatment, tempering and other technological processes.、The use of clean and environmentally friendly natural gas as fuel effectively avoids the adverse effects of chemical reactions between impurities such as coal-fired furnaces and forgings during heating. At the same time, natural gas has high calorific value and high combustion temperature, and the combustion temperature can be further increased by preheating air and fuel. In addition, the gas forging heating furnace also has good heat loss control ability and intelligent control system, which can accurately adjust the ratio of air to natural gas, ensure full combustion of natural gas, and reduce mechanical incomplete combustion and chemical incomplete combustion.、Adopting advanced combustion technology and materials, it has a long service life and low maintenance cost.、Usually equipped with intelligent control system, it can automatically adjust the parameters such as gas supply and air flow according to the heating demand, and realize accurate control of the temperature and atmosphere in the furnace.、Adopting advanced combustion technology and materials, it has a long service life and low maintenance cost.，multifunctional, with functions such as temper, hardening and tempering, Casting heating, anneal and normalizing，Cheap and high quality。

1、Brief introduction of Mold quenching furnace chamber type

Mold quenching furnace chamber typeIt is a forging heating device using gas as fuel.，at the start of the operation,The high-temperature flame and flue gas generated when the fuel burns in the furnace are used as heat sources to heat the medium flowing in the tube to reach the specified process temperature. Fuel is ejected from the burner and burned, resulting in high-temperature flame and high-temperature flue gas. The high-temperature flame transfers heat to the furnace tube in the radiation chamber through radiation, and then to the medium in the furnace tube. The high-temperature flue gas enters the convection chamber of the heating furnace upward due to the suction force of the chimney or the action of the induced draft fan, and the heat is transferred to the furnace tube in the convection chamber by convection, and then to the medium in the furnace tube.，generally, it is composed of ventilation system, convection chamber, ventilation system, recovery of waste heat, ventilation system and other major components。

Mold quenching furnace chamber type

2、Mold quenching furnace chamber type introduction video

On-site aerial photography of Mold quenching furnace chamber type。

Mold quenching furnace chamber type

As you can see from the live video.，Shandong yiran energy-saving environment protection co., ltd is a Mold quenching furnace chamber type。

3、Mold quenching furnace chamber type application

Mold quenching furnace chamber types have the following purposes.

1. Metal melting and casting

Although it is mainly used for forging heating, some types of Mold quenching furnace chamber types can also be used in metal melting and casting processes. This is especially suitable for melting and casting of small or special alloys.

2. Metal forging heating

The Mold quenching furnace chamber type can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

3. Metal heat treatment

In addition to forging heating, Mold quenching furnace chamber types can also be used for metal heat treatment processes, such as annealing and tempering. These processes can improve the microstructure and properties of metal materials, and improve their service life and mechanical properties.

4. Metal tempering

By properly heating and cooling the metal material, the Mold quenching furnace chamber type can realize the quenching and tempering treatment of the metal. This is helpful to adjust the hardness and toughness of metal to meet the needs of different workpieces.

5. Metal melting and casting

Although it is mainly used for forging heating, some types of Mold quenching furnace chamber types can also be used in metal melting and casting processes. This is especially suitable for melting and casting of small or special alloys.

Mold quenching furnace chamber type

4、Mold quenching furnace chamber type use

The purpose of Mold quenching furnace chamber type is introduced as follows:

1. Energy conservation and environmental protection

The Mold quenching furnace chamber type uses clean energy as fuel, which has lower emissions and higher energy efficiency than traditional coal-fired or oil-fired stoves. This is helpful to reduce environmental pollution and realize green production.

2. Improve production efficiency

The Mold quenching furnace chamber type has the advantages of fast heating speed and accurate temperature control, which can improve production efficiency. This is especially important for mass-produced forging workshops.

3. Metal forging heating

The Mold quenching furnace chamber type can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

4. Metal heat treatment

In addition to forging heating, Mold quenching furnace chamber types can also be used for metal heat treatment processes, such as annealing and tempering. These processes can improve the microstructure and properties of metal materials, and improve their service life and mechanical properties.

5. Metal melting and casting

Although it is mainly used for forging heating, some types of Mold quenching furnace chamber types can also be used in metal melting and casting processes. This is especially suitable for melting and casting of small or special alloys.

Mold quenching furnace chamber type

5、Physical picture of Mold quenching furnace chamber type

HD picture of One-combustion energy saving Mold quenching furnace chamber type,energy-efficient。

Mold quenching furnace chamber type

Note: All the pictures in this article were taken by One-combustion energy saving manufacturer.。

6、Introduction of advantages of Mold quenching furnace chamber type

Mold quenching furnace chamber types have the following advantages.

1. Extend the service life of equipment

The Mold quenching furnace chamber type adopts advanced combustion technology and materials, which has a long service life and low maintenance cost.

2. Uniform heating

The Mold quenching furnace chamber type adopts regenerative combustion system or advanced burner design, which can realize uniform distribution of temperature in the furnace, ensure uniform heating of metal materials and improve product quality.

3. Intelligent control

The Mold quenching furnace chamber type is usually equipped with an intelligent control system, which can automatically adjust the parameters such as gas supply and air flow according to the heating demand, and realize accurate control of the temperature and atmosphere in the furnace.

4. Wide application range

The Mold quenching furnace chamber type is suitable for forging and heating of various metal materials, including steel, aluminum and copper. At the same time, it can also be used in metal heat treatment, tempering and other technological processes.

5. Efficient combustion

The Mold quenching furnace chamber type adopts advanced combustion technology and control system, which can realize full combustion of natural gas and improve combustion efficiency. At the same time, some equipment is also equipped with waste heat recovery system, which can further recycle the waste heat in exhaust smoke and improve energy utilization efficiency.

Mold quenching furnace chamber type

Mold quenching furnace chamber typeIt can be used for Metal melting and casting, Metal heat treatment, Metal tempering, Metal tempering, Energy conservation and environmental protection, Metal forging heating and so on，The user interface is friendly, and the operator is easy to use. At the same time, the equipment also has the function of fault diagnosis and alarm, which can find and deal with abnormal situations in time.、Uniform heating and precise control can be realized, so it is helpful to improve the product quality and yield of metal materials.、The use of clean and environmentally friendly natural gas as fuel effectively avoids the adverse effects of chemical reactions between impurities such as coal-fired furnaces and forgings during heating. At the same time, natural gas has high calorific value and high combustion temperature, and the combustion temperature can be further increased by preheating air and fuel. In addition, the gas forging heating furnace also has good heat loss control ability and intelligent control system, which can accurately adjust the ratio of air to natural gas, ensure full combustion of natural gas, and reduce mechanical incomplete combustion and chemical incomplete combustion.、The metal material can be heated to the required temperature in a short time, and the production efficiency is improved.、Efficient combustion and waste heat recovery system can significantly reduce energy consumption, thus reducing operating costs.。